![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
|
Peugeot 3008 Key Fob Problems The mid-sized SUV from Peugeot 3008, has many positive attributes. It looks smart, drives well and has a big boot. Can it compete in the most competitive segment of the market perhaps? If your Peugeot keyfob does not work, it may have been exposed to clean or soapy tap water. You may have to remove the battery and clean it using electronic cleaner or isopropyl alcohol. Dead coin battery Peugeot key fobs are powered by the size of a coin. This power is used to control the remote locking system as well as other features. This battery has a limited time of life and will get worn out after years of use. One way to determine whether the battery is in good condition is to run an electrical test. A multimeter can test the voltage between the battery's plus and poles. This test will determine if the battery is dead. If you've been using your Peugeot 3008 for a while and your key fobs aren't working, there could be a problem with the receiver module. The receiver module is responsible for capturing radio frequency signals from the key fobs and transferring them to the vehicle's systems. If the receiver module has an issue, it will not be able to send commands to other modules inside the car. Another common cause for a non-working key fob is moisture or sweat that has accumulated on the circuit board. This can cause short circuits that drain the battery and disable the feature that locks the fob's remote. If this is the case you must bring your key fob into a chip level technician to repair it. Water damage If you dropped your key fob in the pool, tossed it into the wash or left it in the rain for too long, water damage can be a real problem. Water makes for a good conductor and can quickly damage the components of the circuit board. It can also cause corrosion to the metal traces on the key fob and other components. A wet circuit may cause the battery to lose its charge. If you have an extra key fob, you can use it to lock or unlock the Peugeot 3008 to eliminate a dead coin-cell battery as the cause of the problem. Interference signals can cause your key fob to stop working properly. They interfere with the signal generated by the receiver module. These interference signals can come from a wide range of sources such as radio transmitters in close proximity. If you hear sloshing sounds emanating from your Peugeot 3008 while driving, this is likely caused by a blocked condensate drain from the evaporator. You can test this by blowing compressed air into the drain holes in your door. You can also use a flexible wire to wiggle the drain holes and dislodge any dirt that has built up there. The sound of sloshing could also indicate that there are air pockets in the coolant system. Receiver module that is defective The receiver module in the receiver module of a Peugeot 3008 is responsible for transmitting an electronic remote keyless signal from the keyfob into the receiver in the car. If the receiver module is damaged, it will hinder the car's ability to recognize the key fob. Other factors that can trigger the issue include dead batteries or water damage, as well as interference from electronic devices that operate at the same frequency the key fob. In these cases the car might display the message "card not detected" on the display. There are a variety of ways to fix this problem. You can try replacing the battery or reprogram the key fob. You could also use a spare key in order to start the car. However, if the key fob isn't working even after all these steps, it could have a chip that is defective. Faulty keyless entry systems If you are seeing "card not detected" This indicates that your car isn't receiving a signal sent by your key fob. This can be due to many reasons including an insufficient or dead battery. Most often, the issue can be resolved by pushing the start button using the key fob. In some cases you may require taking the keyfob to a Peugeot dealer for further repairs. The first step to fix the problem with a Peugeot 3008 key fob that doesn't open or lock the doors is to check its battery. Batteries are often the cause of malfunctioning key fobs. However, there are also other causes that could be involved. These include worn buttons and water damage. If you've recently experienced the Peugeot key fob exposed to clean tap water, it's best to remove the battery and dry the electronic components with paper towel. You can also use isopropyl Alcohol or cleaning solution to do this. If the fob has been exposed to salt or soapy water, it's best to replace it.
|
