![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
|
Peugeot 208 Key Replacement Peugeot 208 key replacement should be left to experienced auto locksmiths who have the appropriate equipment and know-how. They will be able to make and program new keys much faster than a dealership would and at a lesser cost. A dead coin battery is most likely to be the cause if your key fob stops locking or unlocking the doors. There are also other reasons why the key may be malfunctioning. Dead Coin Battery A dead battery in the coin compartment will hinder your Peugeot 208 from locking or unlocking and will not start the engine. In this case you'll need make use of the alternative method for starting described in your vehicle owner's manual. Another reason why your 208 might not be starting is that the spark plugs have been worn down. The spark plugs light the fuel to start the engine. They have a limited lifespan. They'll eventually break down when they aren't used enough. There is a simple solution to this issue. Examine the voltage of your battery using a multimeter. If it's lower than 11.5 volts, then you need to replace it. It is also essential to clean the contacts of the battery in case it is corroded. You can do this by lifting the rubber covers covering both battery terminals and using a wire brush to remove any corroded components of the battery. Then, reconnect the positive and negative pole cables. Water Damage If your 208 doesn't start and the battery is not empty, you must ensure whether the spark plugs are working. It is possible that they are just overly filthy, making them unable to spark. The spark plugs can be cleaned in a workshop. Peugeot cars have a transponder style key that works with the car's immobiliser system. This guarantees that only the right key is able to turn the engine. If https://www.thekeylab.co.uk/peugeot-car-keys/ inside the Peugeot key is damaged then it won't send the proper signal to the vehicle. Water damage is a typical reason for this issue. This is most common in colder climates. the vehicle might have been exposed to rain or snow. In this case, contact a reputable locksmith who has the tools and equipment needed to reprogram the key. They will also have the most up-to-date technology and the machinery needed to create a Peugeot 208 smart key. The process should not take more than 15 minutes. Faulty Battery Contacts Peugeot changed from the carbon-encased transponder chips to an entirely new kind of chip that utilizes electronic components that are placed on circuit boards. The new system is great in its initial state, but the circuit boards wear out over time and cease to function properly. This could prevent the immobiliser chip from triggering the immobiliser chip, causing your car not to start. If this is the case, it's a good idea seek out a Peugeot specialist or locksmith. Another issue that is common is when the key fob battery is dying, this causes the key blade to stop feeding into the lock. A locksmith in your car will replace the battery and then cut a new blade for you. This is a quick solution. Faulty Receiver Module It could be that the receiver module is malfunctioning when your Peugeot key fob isn't working after being dropped on the floor, or exposed to a stormy rainstorm, or accidentally washed. The receiver is responsible for transmitting radio frequency signals to the onboard computer which controls the centralized locking system within your Peugeot vehicle. Rubber seals on the key fob keep water from reaching its electronic chip. The chip can be damaged by water if it is exposed to water for a prolonged period of time. The high salt content of the ocean water or pool could cause damage to the key fob if it is submerged. The module will have to be replaced if your Peugeot spare key is no longer working. This is only done by a skilled auto locksmith or Peugeot specialist. Like other automobiles, Peugeot keys are protected by an exclusive immobilizer system that requires the correct coding in order to start the engine. This is the reason why you should only be able to trust a professional Peugeot locksmith to take on the job of designing and programming an alternative. Computer on board is not working properly The computer on the board of your Peugeot is responsible for a number of the systems in your vehicle, from power windows to the airbags. If something goes wrong with these systems, they will usually display a code that indicates the issue. This code is stored in the system and stays there until the problem has been resolved. This will often require the on-board computers to be replaced. The most common cause of the airbag warning light to illuminate is corrosion or loose connections within the sensor. This can be caused by wear and tear, age or exposure to moisture and salt. It is crucial to get this issue addressed as soon as possible, since the airbag malfunctioning could be risky in the event of an accident.
|
