prestoncox119280

Reasons Your Fiat 500 Key Fob Won't Work

A key fob for the Fiat 500 is a convenient method to unlock the doors and get started the car. There are a variety of reasons why the fob may stop working. This could be due to a dead coin battery, damaged receiver module, water damage issues, or interference.

This listing is for a NEW replacement Fiat Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that the 500 key fob won't function is due to an inactive battery. Modern key fobs only have limited operating range and must be within a few inches of your vehicle to work. If you are far from your vehicle and press the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a fresh one of a reputable brand like Panasonic Duracell or Energizer. You can usually find them at your local hardware store or on the internet.

After you've changed the battery on the coin cell You can test it by standing in front of your Fiat 500 and pressing the buttons. The car should blink its parking lights and the key fob should work the lock and unlock buttons.

If the fob's remote doesn't work after replacing the battery, it may be damaged by water, which prevents it from communicating with the receiver module inside your car. Water damage can happen in a number of ways, from the slightest splash to submerging the fob salt water at the beach. If you suspect your fob has been exposed to water, try placing it in a dry rice bag to draw the moisture out. If that doesn't work, your fob is likely to require reprogramming by a professional locksmith or dealer.
https://www.g28carkeys.co.uk/fiat-car-key-replacements-near-me/ can occur if you immerse the fob into the ocean or wash it in a washer. Saltwater poses a particular risk to the circuit board of the fob which causes it to short out and eventually die. It's not a good idea to submerge the fob in water but don't give up in the event that you accidentally drop it in the water or don't remove it from your pocket.

img width="447" src="">
First take the battery off the fob. Before replacing the battery clean the electronic chip with isopropyl or similar products. Check the fob again to check if it's functioning. If the key still doesn't work, it might need to be changed. This is typically handled by a dealer or professional auto locksmith.

If your key is old and is not programmed for your car, you will need to replace it completely. A professional automotive locksmith can complete this simple process. The locksmith must cut the key to match the ignition of your vehicle. The locksmith will also need to program your fob into the car's system. This is a quick and inexpensive process that can usually be completed on the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote's range is of 30 feet. So should you be too far from your vehicle it will not respond to your commands. You can easily solve this problem by moving the remote closer to your car until it responds.

If your fob does not work after replacing the battery for the coin, also called a "button", "watch" or "button" It could be due to a problem with the circuit board inside. In most cases, reprogramming the fob can resolve the issue. You can find instructions on how to do this on the majority of vehicles by searching YouTube or looking through the owner's manual.

It is possible to replace the metal retaining clips that hold the coin battery. If they lose tension, they could stop the battery from sitting properly and can result in the malfunction of your remote.

In rare cases, the fob may become disconnected from your vehicle due to software issues or hardware issues. This could cause a significant issue, but you are able to often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob. In some instances they may have to install the software again in your body control module as well.

Interference

Interference can also cause the key fob not to receive or transmit signals. This may happen if the keyfob is in close proximity to a radio transmitter, such as a cell phone or radar detector. Other reasons the key fob may not function could be due to a weak connection to the buttons or damage to the internal chip or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. replacing batteries, reprogramming or using the spare key fob, you might have a malfunctioning receiver module on your 500. The receiver module, located under the dashboard, picks up radio frequency signals from your key fob. It transforms the signals into electronic commands that are then read by the vehicle.

There is a simple way to reset the 500's onboard system, including the keyfob. Disconnect the battery 12 volt for about 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will clear out any remaining electricity and restart the car's computers, which could allow you to get your key fob working again. If the issue persists, you should consult an experienced technician. They will be able to determine the exact cause of issues.