![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
|
Patio Screen Door Repair - How to Do it Yourself A damaged or worn patio screen door is not just ugly, but it also creates an easy entry point for pests like mosquitoes and insects like flies. While there are services to repair your patio screen door, it's quite simple to complete the job yourself. Then, lay the screen on a flat work surface. Remove the handle from the screen by removing the screws holding it in place. Damaged Screens Between the weather children, pets, and weather It's no wonder that tears and holes will eventually appear on your window or door screens. Apart from looking ugly, these damaged sections allow insects and flies to enter your home. Repairing these problems is simple. While patch kits and screen repair tape provide an easy fix for minor damage, they don't work well on more serious issues. This step-by-step guide will show you how to repair and replace your screen doors and windows. The first thing you need to do is determine the damage. Is the frame salvageable, or does it need to be replaced? It is important to consider this since the frames of window and door screens are more susceptible to being damaged than mesh. A bent frame could cause the screen to be out of alignment, causing holes or weak spots. Once you've determined whether or not the frame is salvageable, you can begin to tackle the mesh. You'll need a few tools to complete the task. A spline roller to press the spline into the frame, scissors and a utility knife are all necessary for this procedure. These tools will ensure accuracy and durability when you make repairs. If you've got a large hole in your screen, start by removing as much as possible of the old material to make a clean space. Then, cut a patch of the new screen material to ensure it is at a minimum half an inch larger than the damaged area. The patch should be matched to your window's grid pattern in the event that it has one. Then, cut the edges of the patch to remove any irregularities and fold them over the top of the spline in order to hide the edges. When purchasing your replacement screen, be sure to consider the climate in your region. Aluminum screens are sturdy and resistant to snags, while fiberglass mesh is popular for its low cost and flexibility. You could also opt for a specialized insect screen mesh if your region is a victim of mosquitos and other insects. Whatever kind of insect screen you choose, make sure you stretch it tightly across the frame to prevent sagging or wrinkles. Broken Rollers A damaged roller on your patio screen door could be a harrowing issue. Not only does it make the process of sliding your door more difficult however, it can also allow insects and other unwanted visitors to enter your home. The good news is, fixing your rollers won't be nearly as expensive or complicated as replacing your door. Begin by looking at your rollers to find the problem. It could be that the wheel has flattened or worn out on one end because of the constant contact with track. You can try to take off the wheels by putting a screwdriver between the bracket and the roller. If you're unable to get the roller to come off, it may be beneficial to spray the shaft area with WD-40 prior to attempting again. Also, you should check the tracks from top to bottom. Straighten bent tracks by hammering a block of wooden against the bent part. It is important to keep the tracks clean as well as they can collect grit and dust. Once you've identified the kind of roller that's broken, you can purchase a replacement. Bring your old rollers to the hardware store so that you can ensure you're purchasing the correct type. If your door has more than one roller then you'll need to buy enough to replace them all. Use a screwdriver to the inside of your door frame, near the rollers to loosen the screws or bolts that adjust the door. After the screws are loosened, you can remove rollers from the bottom. This is best performed by a person else so that you don't need to use your hands. After installing the new roller The door can be raised and the bolts or screws for adjustment can be are tightened. Make sure to verify the alignment of the rollers and track, too. If everything is in its proper position the patio screen will slide into place easily. Frame Damaged There are many ways to repair your screen door that is rubbing against its frame. First, ensure that the hinges are in good condition. A door can bind if the hinges are loose. If they are loose, simply tighten the hinge screws. If this doesn't work, you might need to sand the top of the frame. Another common issue with screen doors is a rotting frame. It can be expensive to fix, since it typically involves replacing the entire frame. To avoid this, be on the eye out for signs of rot and address them immediately if you notice them. Check for signs of rot by looking for soft wood that appears darker than the rest of the frame. Also, keep an eye out for areas where the wood is beginning to bow or warp. Call a professional if you notice any of these issues. A mesh patch kit can be used to repair damaged frames. The cost of these kits is between $2 to $7. The kit comes with a small piece of mesh and glue that you can use to fill any holes in your screen. If the damage isn't too severe, you can also try fixing it with a wood filler. To do this apply the filler on the damaged area, wait for it to dry, and then sand it to a smooth finish. You can purchase a framelift, which is a metal structure that is bolted on to the frame you already have that lifts it up. It is a costly option, but is the best if your frame has been badly damaged or rotted.
Broken Splines A broken screen spline is just as frustrating as damaged frames or doors. It may appear to be a minor issue that can be ignored, but letting it go too long could let pests like mosquitoes and flies to pass through. https://longshots.wiki/wiki/10_Inspirational_Graphics_About_Patio_Door_Lock_Repairs_Near_Me can quickly turn into a larger problem that could lead to costly repairs or a new screen door. It is simple to replace a broken spline, particularly if you have the right tools. First, you'll need take off the old screen door spline. This can be done by laying the frame flat on a surface such as a table, or the ground. Use a screwdriver to pry open the free spline, and then pull it out. If the spline appears to be particularly damaged or brittle, you might find that it breaks as you attempt to remove it from the groove. As you remove the old spline, make sure that you also remove the caulking used to hold it in place. This will ensure that the new spline will be capable of fitting into the grooves. Once you have removed all of the old spline, you can use a utility knife to trim any screen that is left around the frame. This will ensure a tight and clean fit on all sides of your frame after you install the spline. Installing the new spline is simple after you've cleaned the frame and cut the new screen material to the appropriate size. Start on the short side of the frame. Incorporate the spline into the screen channel using your splining device. Continue rolling the spline, and pushing it into the screen channel as you go. Continue this process for each short side of the frame. While you are working, use tape or spring clamps to keep the screen taut. Once you have splined each of the short sides of the frame move to the opposite side and repeat the process. Finish by splining both the bottom and top edges of the frame. |
