![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
|
Patio Door Lock Repairs Over time, patio doors go through wear and tear which can result in locks that fail. There are a few basic steps you can follow to ensure the security of your uPVC door. It's about realigning the lock or cleaning the locking mechanism these simple fixes will make your home more secure. Clean the Lock Patio doors are fantastic for bringing the outdoors in and keeping out the elements. However they can pose risky for security in the event that the lock isn't working correctly. Over time, wear and tear, hot and cold weather dirt, and other debris can cause your patio door lock to become difficult to operate. Fortunately, with a little care, you can ensure your patio door's locks always work effectively. In the beginning, it's essential to clean the lock on your patio door and all the moving parts. This will help to remove any dirt or coatings that might be hindering the lock from working correctly. Start by wiping down the moving parts of the lock for your patio door using a damp cloth. then employ a scouring pad or rough damp cloth to scrub the hard-to-reach areas of the door and frame that are coated with dirt. You should then wipe down the entire lock with dry cloth to get rid of any remaining dampness and allow it to air dry prior to applying it to the next time. If your patio door is equipped with pin-tumbler latches You can apply powdered Graphite on the key. You can also apply a Teflon lubricant like WD-40 Multi-Use Product. This type of lubricant is able to be applied quickly and does not dissolve over time. If you are unable to locate an appropriate lubricant You can try using a pencil with an extremely thick tip. Put the pencil in the lock, then shake it around to distribute the graphite. Regular maintenance is also necessary to keep the tracks of sliding patio doors clear of dust, dirt and other debris. They are particularly susceptible to snow, ice and other debris that can cause them block or become stuck. This can make it difficult for your patio door to open and close. Sliding patio door track rails and rollers can be cleaned by removing damaged or dirty weather stripping and cleaning them before reinstalling it. The same is true to patio door rollers which can be wiped down and then sprayed with a non-stick lubricant to help them move freely. Lubricate the Moving Parts uPVC French doors, like sliding patios, operate using 3 to 4, or sometimes, 5 points locking mechanisms. These include the lock cylinder and handle which is operated by the key. These doors also need maintenance, specifically lubrication on the moving parts. This can be accomplished using an oil that is thin (never WD40) and should be done once per year. If the hinges aren't causing the issue it could be because the door is not aligned. It may be rubbing or catching the hole of the strike plate in the frame. The solution is to take off the strike plate and use an abrasive chisel to increase the size of the mortise that it rests in. This will allow the latch to fit properly into the hole, and prevent it from scratching against the frame. Find the length of the cylinder using a piece of wood or a book that is able to fit into the space above the adjustment screw. The outer dimension is measured from the outside of door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder. Verify the lock's width If your patio door latch is difficult to turn even after cleaning and lubricating, there's a possibility that it's out of alignment with the strike plate hole. Check if your door is in a balanced position, and that the hinge screws are secure. In a lot of instances, moving the strike plate downwards or upwards could fix the problem. Most of the time, the issue occurs when the lock's strike is too small for the latch to engage. In this case, enlarge the opening using the hammer and chisel. Then, test the latch so that it doesn't rub against the jamb frame of the door or get caught the frame. You must identify the kind of mortise lock that you have before buying an alternative. This can be done by looking at the faceplate and noting whether it is round or square. Then, take a look at the screw holes in the existing lock and note the dimensions of each. This will enable you to find an alternative lock that is exactly the same width and will fit in the hole that you already have. In addition to identifying the current mortise lock, you'll also want to inspect it for any scratches or bends that may need repairing. A bent or damaged latch is more prone to break than one that's not used much, so be sure to replace the lock with a new, secure version if you find any signs of wear or damage. After you've examined the lock and identified which type of replacement you'll need, it's time to start working on the actual repair. The spindle and handle should be removed from the patio door. Introduce the new handle. Begin by installing the interior handle. Align it with the spindle, and then secure it into by using two bolts or screws. Once the interior handle is installed, put in the exterior handle and screw it into place, too. After you've completed these steps check the handles to ensure that they open and shut easily and that the latch engages properly with the strikeplate. Check the door's Strike The strike plate and the door latch are two pieces which work together to secure the door. Misaligned strike plate and door latches will result in the latch not being able to latch the door correctly. https://www.repairmywindowsanddoors.co.uk/patio-door-repairs-walsall/ is typically simple to solve. Check the receiving holes of the strike plate to make sure they are clear of obstructions such as dirt or plastic plugs. Release the screws that hold the strike plate in position. This allows it to move vertically but not separate it from the frame. Then, adjust the strike plate so that its receiving holes align with the latch hooks on the door latch. Once the strike plate is adjusted tighten the screws, and test the door to see if it shuts smoothly with the new adjustment. These plates are difficult to reach for homeowners with sliding patio doors. However they are vital for locking and unlocking your door. The plates made of metal are located between the top and bottom jambs of your door, where they support its latch. Then, the door latch slides into the strike plate to create the seal when it is closed. If the strike plate is damaged or rusted or not properly installed the latch may not lock the door properly. The most common reason for a patio door lock to stick or not close is a misalignment of the latch and the strike plate. The most effective way to test for this is to perform the "lipstick test." Apply some lipstick along the edge of the deadbolt and put masking tape on it. The lipstick will leave a mark when you shut the door. This will indicate exactly where the latch connects to the strike plate. If the mark is too high or low, you can easily adjust the strike plate.
|
