lemminggallagher221046

Patio Doors Repair - How to Fix a Wet Dog and Save Your Dog From Cold, Wet Feet

Patio doors are a great option to connect your home with the outdoors. They provide a comfortable and easy transition. They can also save you money on cooling and heating costs by keeping the air inside your home.

However, over time your sliding glass or French doors can lose their luster. Simple repairs can keep your sliding glass or French doors looking and working like new.

Weatherstripping

It's 5 AM and you're letting your dog out for his morning constitutional when you step into the puddle of water by your sliding patio doors. You turn around to see that the rain of last night ripped through the seals of your patio doors. Don't panic and be prepared for this to be a five-minute project. However, with a little patience and some tools to fix this, you can get it fixed and protect your dog from wet, cold feet.

It is important to replace the weatherstripping that seals off the gap between your door and jamb. This will stop drafts, pests, and moisture. This will also help keep your energy costs down. If you check your doors and windows, you will be able to tell whether the weatherstripping has to be replaced or not.

There are many kinds of weatherstripping available, including felt, open-cell foam and thermoplastic rubber, and metals like bronze and copper. Each has its pros and drawbacks. Open cell foam and felt are inexpensive, but they tend to be ineffective and noticeable at blocking airflow. Vinyl is more costly, however, it's more durable and resistant to moisture. http://sc.sie.gov.hk/TuniS/www.repairmywindowsanddoors.co.uk/patio-door-repairs-luton/ is a great choice for areas that are heavily used because it won't wear out as easily.

To install new weatherstripping, you must first remove the patio door from the frame by loosening the roller adjustment screws using the aid of a screwdriver. Then, with a flathead screwdriver, loosen the plugs that secure the weatherstripping at the bottom of frame. Remove the old weatherstripping from the frame, and then remove any adhesive residue. Then, cut the new to the proper length, peel off the plastic strip at one end, and apply it using a putty-blade to the jamb.

Reinstall the door, and adjust the roller screws to ensure it sits properly in the track. Apply waterproof caulk wherever the stationary panel obstructs the sliding doors and at the point where the edge of the panel is the frame. This is a less secure seal than weatherstripping but should work for some time.

Locks and Handles

Patio door handles and locks play an important role in the security of your home. Over time, they can get damaged or worn out and require replacement. The spindle that connects the interior and exterior handles can also be replaced.

img width="336" src="">

To replace a handle on a patio door, remove the previous one first by dislodging any screws that held it in the place. Once the old handle is removed then use a level to make sure the door is straight prior to installing the new handle. If the door isn't straight it could cause problems with the lock and cause problems later on.

Once you have the new handle installed, close and open it several times to make sure it functions effectively. If you have any issues, consult the manufacturer's instructions or a specialist in hardware for assistance. To avoid future issues, it is recommended to also lubricate the lock mechanism using lubricant made of silicone.

The most common door lock for patio doors is the mortise latch. It is usually made of metal and sits inside a pocket which has been cut into the door frame. These locks are typically used on sliding wood and aluminum doors. Before you purchase a new mortise lock, it is essential to measure. The measurements you require include the mounting hole locations and the location of the keyway within the lock.

Some patio door handles come with the ability to lock the handle. They have a rectangular key cylinder that fits into the handle's keyway. This type of patio door comes with the exterior and interior locks in one piece. This kind of patio door are typically found on sliding aluminum doors.

If your patio door latch isn't able to stay closed the lock tongue might not be properly catching the hasp. Another possibility is that the sliding door isn't fully parallel to the jamb's side. The door should be opened an inch, and spot it against the frame. This will tell you whether there is a gap between the door jamb and the door. If there is, you can adjust the rollers on the lower left or right side of the patio door to make it in perfect alignment with the jamb.

Misalignment

Over time the door's tracks and rollers will lose their proper alignment. This can cause the door to sag or become difficult to move. It can also allow drafts and cold air enter your home, which reduces energy efficiency. Fortunately, misalignment can be easy to fix and avoid. Applying a silicone-based oil to the rollers and tracks can allow your doors to glide again. It's a good idea to apply this every so often to keep your doors in peak operating condition.

Another common issue with patio doors is a ripped screen, which could be an issue or even a safety hazard. It may also hinder the doors from closing and opening properly, leading to energy loss. In some cases, the screen can be repaired, but in other cases the door needs to be replaced. If you're experiencing a ripped screen, clean it thoroughly and be sure not to turn the handles of the door the wrong way when opening and closing.

Over time, hinges can loosen due to normal wear and tear or excessive usage. This can be fixed by tightening screws regularly. This is a simple job that you can do yourself, but if not comfortable doing it, seek out an expert to ensure that your doors are correctly aligned and secure.

You should also clean the rollers and tracks of your patio doors on a regular basis. A simple vacuuming or brushing can get rid of dust and debris that could hinder the smooth operation of your patio doors. You can utilize a special tool for stubborn dirt or corrosion. It is possible to correct any misalignment by tightening, or examining the screws. But, at times, it is necessary to replace the hinges in order to ensure a long-lasting seal.

The alignment and performance of your patio doors could be affected when the frames are sagging or sagging. Shifting or warping can occur due to changes in the foundation of your home, but could be caused by poor installation or simply through frequent use. A professional can repair or replace your patio door frame and ensure it's aligned properly and functioning at its best.

Rollers

The sliding patio doors can be a great way to bring the outside in and let in lots of light, but they need some attention to ensure that they're moving smoothly. If you notice that you need to push the handle to get your door to move, or it simply doesn't move as smoothly as it used to then the problem could be the rollers. Over time, the lower track will fill up with dirt, sand and mud that makes it difficult for the rollers to move over. You can clean it up and spray it with a lubricant like 2Slick to determine if it helps.

If the tracks have been cleaned but the rollers aren't moving freely, then it is time to replace them. There are a variety of replacement rollers to match your door and the type of track you have. These can be purchased at many hardware stores, however you'll need a friend to assist with the removal and installation of the rollers. Before ordering replacements, get an accurate picture of the roller assembly that is placed in the door frame, so experts can identify the exact model and type you require. You can also search for specific features like dimples or bumps or cutouts, flared edges or cutouts to narrow down your replacement options.

When the rollers are replaced, you'll need to reinstall your sliding door in its frame. Get some help on this one since the door is quite heavy. Start by checking to make sure there aren't any screws securing the track in position on either side of the frame. Also, make sure that they are loose enough to allow the door's bottom to slide into the channel on top of the frame. Remove the screen door from the opening. Make sure it is clear of the track, rollers and track.

After putting in the new rollers, gently place the door into the frame. Swing it down to make sure it is secure. If the rollers are adjustable you can adjust them to ensure that the door has enough clearance.