kringlin680372

Patio Door Lock Repairs

Over time, the wear and tear could cause lock malfunctions. Fortunately, there are several simple and effective ways to restore your uPVC patio door's security.

These simple fixes can make your home safer no matter if you adjust the lock or clean the locking mechanism.

img width="433" src="">

Clean the Lock

While patio doors are a great option to let the outside in and keep out the elements however, they can also pose security risks if your lock isn't working as it should. As time passes wear and tear cold and hot weather dirt and debris can cause damage to the lock of your patio door and cause it to become difficult to open. Fortunately, with a little maintenance you can ensure that your patio door's locks will always perform effectively.

In the beginning, it's essential to clean the lock of your patio door and all its moving parts. This will help to remove any dirt or coatings that might be hindering your lock from functioning effectively. Begin by wiping down the moving parts of the lock for your patio door with a damp, clean cloth. then employ a scouring pad or rough damp cloth to scrub any difficult-to-access areas of the door or frame that are covered in dirt. You should then wipe down the entire lock with a dry cloth to remove any remaining dampness, and allow it to air dry before applying it to the next time.

If your patio door uses pin-tumbler locks you can lubricate it by applying powdered Graphite on the key. You can also apply a Teflon oil like WD-40 Multi Use Product. This type of lubricant can be applied easily and will not disintegrate over time. If you're unable to locate an appropriate lubricant, you might try using a pencil with an extremely thick tip. Insert the pencil into the lock and move it around a bit to spread the graphite.
https://writeablog.net/couchgrey57/five-qualities-that-people-search-for-in-every-aluminium-patio-door-repairs for sliding patio doors require regular maintenance to ensure they're free of dirt, dust and other debris. These tracks can be especially vulnerable to snow and ice, which could cause them to be stuck or jammed and make it difficult for your patio doors to open and close.

The sliding rails of the patio door track and rollers can be cleaned by removing damaged or dirty weather stripping and then cleaning it, before installing it. Patio door rollers can also be cleaned and sprayed down with an oil that is nonstick.

Lubricate the moving parts

uPVC french doors, which are similar to sliding patio doors, operate using 3-4 or sometimes 5-point locking mechanisms that include the lock cylinder and handle controlled by keys. They require maintenance and the lubrication of moving parts. This can be done using an oil that is thin (never WD40) and should be done every year.

If sagging hinges don't cause the problem, it could be that the door is not aligned. It could be rubbing or catching against the strike plate's hole in the frame. Remove the strike plate and employ a sharp tool to increase the size of its mortise. This will allow the latch to fit properly into the hole, and prevent it from hitting the frame.

While the cylinder is out of the way, measure its width with the help of a book or piece wood that will fit in the gap of adjustment screw above the lock. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the width of the lock.

If your patio door latch is difficult to turn even after cleaning and lubricating, it's possible that it's not in alignment with the strike plate hole. Verify that the door is properly balanced and if the hinge screws are in good condition. In many cases, however, simply moving the strike plate downwards or upwards could fix the problem.

The most common issue is when the strike of the lock is too small for the latch to properly engage. In this case, enlarge the opening with a chisel and hammer. Then test the latch to ensure that it doesn't rub against the jamb frame of the door or get caught the frame.

Before buying a replacement lock, it is important to determine what kind of mortise lock you currently have. You can do this by taking a look at the faceplate of the lock and noting if it is square or round. Then, look at the screw holes in the existing lock and note the dimensions of each. This information will assist you in finding an alternative that is the same size and fits perfectly into your existing hole.

You'll need to locate the mortise lock and examine it for scratches, bends or other damage that needs to be repaired. A damaged or bent latch is more likely break than one that's not used much, so be sure to replace the lock with a brand new, secure version if you find any signs of wear or damage.

Once you've identified the type of lock replacement you need It's time to start the actual repair. Remove the handle and spindle out of your patio door, and then install the new one. Start by installing the inside handle. Align it with the spindle and then secure it into position using two bolts or screws. Once the interior handle is installed, put in the exterior handle and screw it in place as well. After you've completed the steps then you can test the new handles to ensure that they can be opened and closed easily and that the latch catches correctly when you strike the plate.

Check the Door's Strike

The strike plate and the door latch are two components that work together to secure the door. A misaligned strike plate or door latches will cause the latch to not latch the door in a proper manner. Fortunately, this problem is often easy to fix.

Check the receiving holes of the strike plate to ensure they are clear of obstructions such as dirt or plastic plugs. Loosen the keeper screws holding the strike plate in place. This will allow it to move vertically, but it will not be able to separate from the frame. Adjust the strike plate to align its holes for receiving with the latch hooks of the door latch. After the strike plate has been adjusted tighten the screws, and then test the door to see whether it locks smoothly after the new adjustment.

Door strike plates can be difficult to access for homeowners with sliding patio doors, however they're crucial for locking and unlocking your door. The plates made of metal are located on the top and bottom jambs of the door which are where they help support the latch. The door latch is inserted into the strike plate and forms an airtight seal. If the strike plate is damaged, rusted, or not installed correctly, it can prevent the latch from locking the door securely.

A misalignment of the latch and strike plate is a common reason for a patio lock to not close or stay. This can be checked with the "lipstick" test. Apply a little lipstick on the outside of the deadbolt. Then cover it with masking tape. When you shut the door the lipstick will leave an impression on the tape, showing exactly where the latch connects to the strike plate. If the mark is too low or high it is possible to adjust the strike plate.

If your patio door locks for sliding aren't working correctly they could be a problem in keeping your home safe from burglars. It is imperative to repair the issue as soon as possible. Follow these easy steps to repair your patio door lock and restore it's function.