![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
|
Peugeot 308 Key Fob Problems and How to Fix Them If your Peugeot key fob suddenly stopped functioning, it could be due to a dead battery in the coin-cell unit or damaged receiver modules, water issues, or even a defective chip. These are all simple solutions and you'll be able to get your car back to speed in a matter of minutes! Car keys can also be damaged because the key blade gets worn. It is easy to fix this problem by visiting your local Car Key Man Auto Locksmith to replace the blade. Battery The battery that powers the key fob on your Peugeot 308 can sometimes die or become weak enough to send an intense signal to your car. This could cause the key fob to stop working which prevents you from opening and locking the doors, or even starting your engine. To fix this issue, you'll need to replace the battery on the key fob. You'll have to purchase a replacement battery from an auto parts store or your local hardware store. Make sure the battery is brand new and not sitting on the shelf too long. A new battery has more capacity and will send a stronger signal your vehicle. After replacing the battery If you have a new battery, try unlocking and locking the doors of your Peugeot by using the key fob. If the doors won't open the issue is likely to be in the receiver module of the car which can be changed by your local Peugeot dealer. It's possible that the key fob's internal chip is damaged. You could damage your key fob if you drop it on the ground or expose it to water. The rubber seals that shield the chip from moisture can wear down over time, particularly if your key fob is exposed to water for long periods of time like submerging it in the ocean at the beach. To prevent this from happening, it's important to protect your key fob from moisture and not let it come into contact with water. Water Damage If your key fob is wet in water, whether you dropped it in the pool or fumbled it into a puddle don't think it's a loss. The key fob is protected by rubber seals but prolonged exposure to water could cause damage to its electronic chip. Water is a good conductor, and any water that is absorbed into the key fob will cause short circuits in series that eventually destroy the electronic chip. After removing the battery clean the contacts with isopropyl Alcohol and dry it off completely before putting it back in.
Another possible cause is a defective receiver inside the vehicle that could block the signal from the key fob. It could be due to a problem with the antenna or wiring, or the key fob might be damaged. If you are using a new key fob, it might need to be programmed into the vehicle. If you are unable to fix the issue on your own, contact an expert technician. A technician trained in the field will be able diagnose the problem quickly, and fix it immediately. Radio Interference Interference can result in symptoms such as a fob that's not being recognized or has a narrow range. It could be radiated or conducted, with the latter resultant from power supply cables and speakers wiring that are too close to electrical components. Usually, rerouting the cables or moving them away from the components can solve the issue. It's unlikely someone is watching the key fob's signal in attempt to steal your vehicle however it is possible that radio interference has ruined the signal. This is an easy issue to solve. If you are having key fob not being recognized, try using a fresh battery. Make sure that the battery is the right size and type. Batteries of the wrong dimensions can harm your battery. These devices may interfere with the key signal if they use the same radio frequency. It is advised to avoid using these devices on your key fob. Pairing Issues The remote keyless entry system in a car has an antenna that receives radio signals from the key fob. If the receiver is experiencing an issue, you will not be in a position to begin your vehicle even if your key fob functions and can be reset. The issue can be caused in a number of ways, including by a dead battery in the coin-cell, or water damage. The receiver could also be faulty due to a software issue or internal damage in the key. The battery that powers your Peugeot 308 keyfob has probably failed. You can easily replace this with a brand new battery but it's essential to select the correct battery for your key fob. https://www.thekeylab.co.uk/peugeot-car-keys/ is best to choose a battery that is the same size with the same voltage, specifications, and specifications as the original. Your Peugeot 308 keyfob may not work if it has been connected to another vehicle. This can happen if you have given your key fob to a friend or it has been used to unlock and start other vehicles. You can fix this by reprogramming the fob using an OBDII scanner. The tool will ask you for details about your car like its VIN or engine type. It is crucial that you enter the correct information. |
