donnellybrowne970666

Fiat 500 Replacement Key Fob

If your 500 remote key fob has stopped functioning, it could be time to replace the battery. If you do replace the battery but it does not work it is likely to be elsewhere.

At United Locksmith, we specialize in making new keys for old cars. We have the tools and components needed for this job.

Dead Coin Battery

The most common reason your Fiat 500 key fob will not lock or unlock the doors is a dead battery. The key fob is equipped with a coin cell battery which will quickly drain when it isn't being frequently used. If your remote has started to show signs of loss in range or stopped working, then the battery may be dead.

The battery inside the key fob is held in place by steel clips for retaining. If the clips aren't secure, they can cause contact issues which will prevent the remote from receiving power. Utilizing a small screwdriver, pull the retaining clip outwards to remove the current battery, and replace it with a brand new one. Make sure that the battery you choose to use has the same voltage, size and specifications as the original.

Exposure to water can cause the key fob to corrode, or even become damaged. Even a brief bath in soapy water can harm the electronic chip in. Keep your key fob dry.

Water Damage

If your key fob isn't operating properly, it may be caused by water damage. The rubber seals on key fobs keep them from getting damaged by a tiny drizzle or splash of water. However, it is essential to keep the keys out of the washing machine, the ocean and even the pool.

The key fob contains an electronic chip inside that sends a signal car's immobilizer system. This is what allows your 500 to start or lock, but should the chip become wet, it can no longer function.

If you're looking to determine if your key fob is functional, you can clean the internal electronics using isopropyl or an electronic cleaner. However, it is probably best to get a replacement from a dealership rather than trying to fix the key fob that is submerged in salt water.

Although a replacement fob may cost you a bit of money, it is much cheaper than having to pay for your Fiat 500 to be towed to the dealer and repaired! You can also make it yourself with only a few steps. Just make sure you have the right battery type before you attempt to open your key fob. https://www.g28carkeys.co.uk/fiat-car-key-replacements-near-me/ can find step-bystep instructions for any car keyfob on the internet.

Faulty Chip

The chip in the key fob communicates with your car's immobiliser system to ensure the vehicle is capable of starting when the correct key is inserted. If the chip is damaged, or corrupted the car won't start, no matter what you do.

A faulty chip can occur due to several reasons, but the most common cause is water damage or a dead battery. It is recommended to leave the repair to a professional locksmith, who can replace the chip in a short time and at a an affordable price.

img width="464" src="">

If your key fob ceases to function after exposure to clean tap water or rain, take out the battery and wipe down the electronic component with a tissue to ensure it's dry before putting it back into. If the key fob will not function, there is an opportunity that it is damaged components and requires to be replaced.

Many people will seek out their dealer when they are in need of an entirely new Fiat key fob, but this can be a very expensive alternative. United Locksmith is the best choice if you would like to have your Fiat keyfob repaired at a reasonable cost. We have the equipment and know-how to fix your Fiat fob in a timely and professional way.

Faulty Receiver Module

Fiat key fobs transmit an electrical signal to the vehicle that can unlock and lock doors (and start the vehicle for those with an automatic transmission) up to 50 feet. There are a variety of reasons why the fob could stop working. This can be caused by a dead coin-battery or water damage, worn out buttons as well as a receiver issue. signal interference or a malfunctioning chip.

If the fob was located in an area that has experienced severe trauma (such as being dropped onto the floor or washed in the washing machine) the fob might not be in a position to connect with the Body Control Module (BCM) of the car. This is because the BCM is secured and will only accept a signal from a genuine original key and not accept any other.

If this is the case, then you will need to replace your fob. A locksmith professional can handle every aspect of the replacement process and can even program a brand new one for your 500. They can even offer a clone fob that works the same as the original (and costs one-third of what it would cost).