閲覧総計:779 (本日:1 昨日:1)
【目次】(項目をクリックすると、そこへ飛べます)
液晶ディスプレイ(LCD:Liquid Crystal Display)へ文字を表示するだけの基本機能の
プログラムを作成し、LCDの稼働を確認した。
また、HI-TECH C PRO(Lite mode)のLCD表示用関数を作成し、稼働を確認した。 08/08/15
LCDは、東京秋葉原の秋月電子で販売されている16文字×2行表示のLCD
SC1602BS-B(-SO-GS-K) 550円 を用いた。 08/08/15
http://akizukidenshi.com/catalog/items2.php?p=1&q="P-00040"
/** * LCD表示(基礎) LCD 4bit接続の確認 * * LCD:SC1602BS-B(-SO-GS-K) 秋月550円 08/08/15 * http://akizukidenshi.com/catalog/items2.php?p=1&q="P-00040" * LCDデータpin D4:RB0 D5:RB1 D6:RB2 D7:RB3 * LCD制御pin EN:RC4 RW:RC5 RS:RC6 * 電源:乾電池3本(4.5V) * * 16F886 * Clock: 8.0MHz 内蔵発振器使用 * Device Flags: * _INTRC_OSC_NOCLKOUT _WDT_OFF _PWRTE_ON _MCLRE_OFF * _CP_OFF _CPD_OFF _BOR_OFF _IESO_ON _FCMEN_ON * _LVP_OFF _DEBUG_ON _BOR21V _WRT_OFF * * MikroC v8.1.0 */ void main() { //PICの初期化 TRISB = 0b00000000; //PORTB全てを0:出力に設定 TRISC = 0b00000000; //PORTC全てを0:出力に設定 OSCCON = 0b01110000; //内蔵発振器 8MHz使用に設定 // A/D利用PORTの設定 ANALOG=1, DIGITAL=0 ANSEL = 0b00000000; //AN4-0ピンはデジタルで使用 ANSELH = 0b00000000; //AN13-8ピンはデジタルで使用 PORTB = 0b00000000; //PORTBの中身をきれいにする PORTC = 0b00000000; //PORTCの中身をきれいにする //PICの初期化終わり //Lcd_Custom_Config(*port, D7, D6, D5, D4, *ctrl, rs, rw, en) Lcd_Custom_Config(&PORTB,3,2,1,0, &PORTC,6,5,4); //LCDのピン接続設定 Lcd_Custom_Out(1, 1, "12345678"); //LCD上位文字列表示 Lcd_Custom_Out(2, 1, "Hello world"); //LCD下位文字列表示 while (1) { } }
★この情報は役に立ちましたか?
/** * LCD表示(基礎) LCD 4bit接続の確認 * * PIC16F886 内蔵 8MHz * LCD:SC1602BS-B(-SO-GS-K) 秋月550円 08/08/15 * http://akizukidenshi.com/catalog/items2.php?p=1&q="P-00040" * LCDデータpin D4:RB0 D5:RB1 D6:RB2 D7:RB3 * LCD制御pin EN:RC4 RW:RC5 RS:RC6 * 電源:乾電池3本(4.5V) * * HI-TECH C PRO PIC10/12/16 MCU Family(Lite mode) v9.60 * MPLAB v8.14 */ #include <htc.h> #include "lcd.h" __CONFIG(INTIO & WDTDIS & PWRTEN & MCLREN & UNPROTECT & DUNPROTECT & BORDIS & IESODIS & FCMDIS & LVPDIS & DEBUGEN); __CONFIG(BORV21); void main(void) { //PICの初期化 TRISB = 0b00000000; //PORTB全てを0:出力に設定 TRISC = 0b00000000; //PORTC全てを0:出力に設定 OSCCON = 0b01110000; //内蔵発振器 8MHz使用に設定 // A/D利用PORTの設定 ANALOG=1, DIGITAL=0 ANSEL = 0b00000000; //AN4-0ピンはデジタルで使用 ANSELH = 0b00000000; //AN13-8ピンはデジタルで使用 PORTB = 0b00000000; //PORTBの中身をきれいにする PORTC = 0b00000000; //PORTCの中身をきれいにする //PICの初期化終わり //添付のsamplesフォルダのLCDemoのmain.cを参考にアレンジ //LCDの初期化 lcd_init(); lcd_goto(0); // select first line lcd_puts("12345678"); lcd_goto(0x40); // Select second line lcd_puts("Hello world"); while (1) { } }
●ポイント:lcd.hとlcd.cはメインプログラムと同一フォルダー内にコピーして入れて置くこと。
(所在:添付のsamplesフォルダのLCDemoフォルダ内)
●lcd.h (添付のsamplesフォルダのLCDemoのlcd.hを変更なしで、そのまま利用)
ファイル内容全てを2013/10/16掲載
/* * LCD interface header file * See lcd.c for more info */ /* write a byte to the LCD in 4 bit mode */ extern void lcd_write(unsigned char); /* Clear and home the LCD */ extern void lcd_clear(void); /* write a string of characters to the LCD */ extern void lcd_puts(const char * s); /* Go to the specified position */ extern void lcd_goto(unsigned char pos); /* intialize the LCD - call before anything else */ extern void lcd_init(void); /* write a character to the LCD */ extern void lcd_putch(char); /* Set the cursor position */ #define lcd_cursor(x) lcd_write(((x)&0x7F)|0x80)
●lcd.c(分割コンパイル)
(自分の使用環境に合わせて変更し利用する)
今回は16F886を用い以下の通り7か所を変更し、ファイルを上書き保存し分割コンパイル
に利用した。
内臓発振器 8MHzで使用するので、
20行 #define _XTAL_FREQ 8000000
今回は、LCDのRSをRC6、RWをRC5、ENをRC4し、D7をRB3、D6をRB2、D5をRB1、D7をRB0に
接続したので、
27行 #define LCD_RS RC6
28行 #define LCD_RW RC5
29行 #define LCD_EN RC4
30行
31行 #define LCD_DATA PORTB
99行 TRISB=0;
100行 TRISC=0;
に変更する。
lcd.c ファイル内容全てを2013/10/16掲載
/* * LCD interface example * Uses routines from delay.c * This code will interface to a standard LCD controller * like the Hitachi HD44780. It uses it in 4 bit mode, with * the hardware connected as follows (the standard 14 pin * LCD connector is used): * * PORTD bits 0-3 are connected to the LCD data bits 4-7 (high nibble) * PORTA bit 3 is connected to the LCD RS input (register select) * PORTA bit 1 is connected to the LCD EN bit (enable) * * To use these routines, set up the port I/O (TRISA, TRISD) then * call lcd_init(), then other routines as required. * */ #ifndef _XTAL_FREQ // Unless specified elsewhere, 8MHz system frequency is assumed #define _XTAL_FREQ 8000000 #endif #include <htc.h> #include "lcd.h" #define LCD_RS RC6 #define LCD_RW RC5 #define LCD_EN RC4 #define LCD_DATA PORTB #define LCD_STROBE() ((LCD_EN = 1),(LCD_EN=0)) /* write a byte to the LCD in 4 bit mode */ void lcd_write(unsigned char c) { __delay_us(40); LCD_DATA = ( ( c >> 4 ) & 0x0F ); LCD_STROBE(); LCD_DATA = ( c & 0x0F ); LCD_STROBE(); } /* * Clear and home the LCD */ void lcd_clear(void) { LCD_RS = 0; lcd_write(0x1); __delay_ms(2); } /* write a string of chars to the LCD */ void lcd_puts(const char * s) { LCD_RS = 1; // write characters while(*s) lcd_write(*s++); } /* write one character to the LCD */ void lcd_putch(char c) { LCD_RS = 1; // write characters lcd_write( c ); } /* * Go to the specified position */ void lcd_goto(unsigned char pos) { LCD_RS = 0; lcd_write(0x80+pos); } /* initialise the LCD - put into 4 bit mode */ void lcd_init() { char init_value; ADCON1 = 0x06; // Disable analog pins on PORTA init_value = 0x3; TRISB=0; TRISC=0; LCD_RS = 0; LCD_EN = 0; LCD_RW = 0; __delay_ms(15); // wait 15mSec after power applied, LCD_DATA = init_value; LCD_STROBE(); __delay_ms(5); LCD_STROBE(); __delay_us(200); LCD_STROBE(); __delay_us(200); LCD_DATA = 2; // Four bit mode LCD_STROBE(); lcd_write(0x28); // Set interface length lcd_write(0xF); // Display On, Cursor On, Cursor Blink lcd_clear(); // Clear screen lcd_write(0x6); // Set entry Mode }
●↓lcd.cの設定(分割コンパイル)
★この情報は役に立ちましたか?